Polarity reversal for biofouling control in ElectroSAnMBR electrodes
Bilge water is a difficult feed stream for any biological treatment system. It can contain diesel residues, lubricants, detergents, corrosion products, suspended solids and changing concentrations of biodegradable organic matter. In the ElectroSAnMBR project, a submerged anaerobic electrochemical membrane bioreactor brings together anaerobic digestion, electrolysis and membrane separation to treat this complex wastewater more efficiently.
Electrodes are central to that process, yet they can become covered by microbial films, precipitated minerals, oil droplets and trapped solids. This layer, known as biofouling when biological growth is dominant, can reduce current transfer and alter the microbial community. Polarity reversal offers a practical research pathway for disturbing deposits, restoring electrode activity and extending operation between maintenance cycles.
| Control approach | Main mechanism | Potential value in ElectroSAnMBR | Key limitation |
|---|---|---|---|
| Polarity reversal | Temporarily switches anode and cathode functions | Disrupts attached biofilms and deposits without dismantling the reactor | Excessive switching may stress electroactive microbes |
| Hydraulic cleaning | Uses flow or backwashing to remove loose material | Helps clear suspended solids and weakly attached biomass | Less effective against strongly attached films |
| Chemical cleaning | Dissolves organic or inorganic fouling layers | Can restore heavily fouled surfaces | May damage membranes, electrodes or anaerobic organisms |
| Current optimisation | Controls current density and gas production | Reduces conditions that encourage excessive growth | Requires accurate monitoring and control |
| Surface modification | Changes electrode texture or chemistry | May limit attachment and improve electron transfer | Adds manufacturing cost and needs long-term validation |
Why electrode fouling matters
An electrode in an anaerobic electrochemical reactor is more than a conductive surface. It can support electroactive microorganisms that exchange electrons with the electrode and contribute to the breakdown of organic pollutants. When a thick or uneven film develops, it may block active sites, increase electrical resistance and prevent wastewater from contacting the useful surface.
Bilge water makes this problem more complex. Oil can form hydrophobic patches, while detergents may change surface tension and microbial attachment. Iron, calcium and magnesium can also precipitate near electrochemical interfaces. A mixed layer of oil, extracellular polymeric substances and mineral scale may be harder to remove than a biological film alone.
For vessels operating near Sydney’s Port Botany, Fremantle or the Port of Melbourne, treatment equipment may encounter different fuel residues and cleaning products depending on vessel type and maintenance practice. A robust control strategy therefore needs to tolerate variable wastewater rather than rely on one stable laboratory composition.
How polarity reversal works
Polarity reversal switches the electrical role of the electrodes for a defined period. A cathode becomes an anode and an anode becomes a cathode, changing local oxidation and reduction conditions. This can disturb the electrical gradients that support a mature biofilm and promote the detachment of weakly bound material.
The reversal event may also create short-lived changes in pH, dissolved gases and redox conditions close to the surface. These effects can weaken extracellular polymeric substances, alter mineral precipitation and help release deposits into the bulk liquid. The process is not a substitute for good reactor design, but it can function as an intermittent self-cleaning measure.
The timing must be carefully selected. Very frequent switching could interrupt beneficial electroactive communities, reduce methane production or expose sensitive organisms to unsuitable conditions. A longer interval may allow excessive fouling to develop before cleaning begins. ElectroSAnMBR experiments can compare fixed schedules with trigger-based operation, using resistance, voltage response and treatment performance as indicators.
Finding the right operating window
A useful polarity reversal programme should define the switching interval, reversal duration, applied current or voltage, and recovery period. These settings should be tested alongside organic loading rate, hydraulic retention time and membrane flux. Fouling at the electrode cannot be assessed separately from fouling in the submerged membrane, because changes in solids distribution and gas production may affect both.
Researchers can track electrode potential, cell voltage, current efficiency, gas composition and soluble chemical oxygen demand. Visual inspection and microscopy can show whether the film is smooth, patchy, filamentous or mineral-rich. Measurements of extracellular polymeric substances, volatile fatty acids and methane yield can reveal whether reversal removes unwanted growth while preserving useful anaerobic activity.
The feed should also represent realistic operating conditions. A useful bilge water comparison can help distinguish results caused by polarity reversal from results caused by the differences between synthetic mixtures and actual ship-generated wastewater. Real samples may include intermittent oil pulses and cleaning chemicals that are absent from simplified laboratory recipes.
Protecting microbial and membrane performance
Polarity reversal needs to be gentle enough to preserve the biological functions of the anaerobic reactor. The objective is to control excessive attachment, not remove every microorganism from the electrode. A stable population of electroactive bacteria may be essential for efficient electron transfer and pollutant conversion.
Monitoring should therefore include microbial recovery after each reversal event. If methane production falls, volatile fatty acids accumulate or current recovery becomes slower, the switching programme may be too aggressive. A staged approach could begin with short reversals at low intensity, followed by longer or more frequent events only when fouling indicators reach a defined threshold.
The membrane system also benefits from balanced solids management. Detached biofilm can increase suspended solids temporarily and may contribute to membrane cake formation. Gas sparging, reactor mixing and membrane relaxation should be coordinated with polarity reversal so that released material is transported away rather than deposited on the membrane surface.
Relevance to Australian maritime conditions
Australian shipping routes connect busy industrial ports with remote coastal areas, where access to specialist maintenance can be limited. A treatment unit that can recover electrode performance through automated electrical control may reduce the need for frequent manual cleaning. This has value for vessels travelling between Brisbane, Newcastle and northern Australian ports, where service availability and weather conditions vary.
The local market also places attention on energy use, discharge compliance and compact equipment. Ship operators may be reluctant to adopt a system that requires high chemical consumption, large tanks or frequent replacement parts. Polarity reversal is attractive for investigation because it uses the existing electrical architecture, although its energy demand and effect on total operating cost must be quantified.
Environmental sensitivity is another important context. Discharges near the Great Barrier Reef, the Torres Strait and densely used harbour areas face strong public and regulatory scrutiny. Australian operators must consider the requirements of the Australian Maritime Safety Authority, port procedures and vessel-specific waste management plans. ElectroSAnMBR research can support this setting by linking electrode stability with pollutant removal, effluent quality and operational reliability.
Turning laboratory findings into field evidence
A convincing evaluation should compare a reactor with scheduled polarity reversal against a similar reactor without reversal. Both systems should receive comparable loading, mixing and membrane operation. The study can then measure fouling rate, electrode resistance, oil and grease removal, chemical oxygen demand reduction, methane production and membrane permeability over an extended period.
Short experiments may show that a surface appears clean immediately after switching, while longer trials reveal whether the biofilm rapidly reforms. Repeated cycles are particularly important because deposits can become more difficult to remove after ageing. Researchers should also record whether reversal changes the size distribution of detached solids or causes pollutants to accumulate elsewhere in the reactor.
For the project’s research partners, the strongest outcome will be an operating envelope rather than a single universal setting. That envelope could specify acceptable current density, switching frequency and recovery time for different bilge water characteristics. It may also identify when polarity reversal should be combined with hydraulic flushing or periodic low-impact maintenance.
ElectroSAnMBR can help move this concept from a promising control technique towards a practical treatment strategy. Follow the project’s experimental progress, research methods and results, and support the development of cleaner, lower-maintenance wastewater treatment for the maritime sector.