Electrochemical Removal of Heavy Metals from Bilge Water
Ship bilge water is a variable mixture of seawater or fresh water, residual fuel and lubricants, engine washings, cleaning chemicals and corrosion products. Copper, zinc and nickel can enter from galvanised fittings, sacrificial anodes, cooling systems, pipework and worn coatings, while lead or chromium may accompany certain oils or additives. The result is a complex, often oily wastewater stream with both dissolved and particle-bound metals.
ElectroSAnMBR is a European Union Horizon 2020-funded research project combining electrolysis, anaerobic digestion and membrane bioreactor technology. Its approach is to use electrical treatment to destabilise emulsions and separate selected contaminants, then use digestion and membrane separation to manage the remaining organic load and capture solids. For an Australian audience, the central questions are whether metals disappear reliably in a beaker and whether the process remains safe, economical and practical aboard real vessels.
Why metal separation aboard ships is difficult
Trace metals cannot be destroyed by biological treatment or oxidation in the way degradable organics can. They may change oxidation state, dissolve, precipitate or migrate into sediment and sludge. Conventional coalescence and filtration can remove metal attached to oil droplets or particles, yet dissolved ionic species often pass through. Electrochemical treatment adds another route by changing metal chemistry and creating solids that can be filtered.
Oil droplets, rust particles and cleaning surfactants can hide metals from analytical measurements or carry them across a separator. High conductivity from salt can make electrolysis efficient, but chloride also affects electrode reactions and may support unwanted chlorine formation. Flow is intermittent, so a reactor must cope with slugs rather than a steady laboratory stream.
The engineering target is therefore selective removal with a traceable destination for captured metals. A low concentration in treated water is not enough if the metal merely transfers into oily filter waste, electrode deposits or membrane sludge. Performance data must include the solids stream, energy demand and any treatment-generated by-products.
How electrochemistry separates metals
In an electrocoagulation configuration, a sacrificial iron or aluminium anode releases coagulant ions that form hydroxide flocs. Copper, zinc, nickel and other metals can adsorb to these flocs or form insoluble hydroxides. The cathode also produces hydrogen and local pH changes that favour precipitation, so removal may combine electrocoagulation, adsorption and chemical precipitation rather than a single reaction.
Current can also drive direct or mediated reduction at the cathode. Metal ions such as copper and nickel may be deposited onto an electrode when their reduction potentials and local conditions align. Anode-generated oxidants can transform some metals into less soluble forms, although the outcome depends on pH, ligands and competing species. Electrode material and polarity must therefore be selected for the target water rather than chosen from one generic recipe.
Electrical oxidation may assist with a separate problem: breaking persistent oils and surfactants that inhibit phase separation. Radical or oxidant pathways can improve oil capture and release metals bound in droplets, but they may also form chlorinated compounds in saline water or partially oxidise organics. Control of current, pH, chloride and reaction time is essential.
These mechanisms are being evaluated alongside physical separation and analytical mass balances. The reactor configurations, test methods and supporting documents are available in the project materials. This integrated view is necessary to distinguish true aqueous removal from temporary transfer into another waste stream.
Combining treatment with anaerobic digestion
A strong design treats the flows as a linked process. An equalisation and oil-recovery stage can remove bulk free oil, followed by electrochemical conditioning, an anaerobic digester and a membrane bioreactor. This sequence protects downstream biological and membrane stages from sudden hydraulic shocks and excessive grease.
Anaerobic digestion converts soluble biodegradable organics into methane-rich biogas while reducing the organic load that would otherwise consume electrical treatment capacity. It may also alter sulfur chemistry, producing sulfide that can precipitate some metals as metal sulfides. That is useful for capture, but sulfide generation must be balanced against microbial inhibition and the risk of releasing hydrogen sulfide.
The membrane bioreactor retains biomass and captures precipitated particles, allowing the liquid phase to be polished without losing all captured solids to the effluent. Membrane fouling, iron or aluminium carry-over, gas production and metal-rich sludge handling remain significant design constraints. A useful configuration must treat the sludge as a managed residue rather than an incidental output.
What controls removal efficiency
Current density and applied charge set the pace of electrolysis, but charge per volume is often more informative. Low current can leave long residence times and poor mixing; excessive current increases electricity use, electrode wear and unwanted chemistry. Electrode area, gap, conductivity, temperature and flow pattern determine how evenly charge reaches the water.
pH is a master variable. It influences anode corrosion, hydroxide formation, metal solubility and the stability of iron flocs. Salinity improves conductivity, while chloride can contribute to chlorine-related by-products. Dissolved organic matter competes for oxidants and can coat active surfaces, so a clean-water result can overstate performance in oily bilge.
Efficiency should be reported for dissolved and total metals separately, with influent and effluent concentrations, replicate runs and analytical uncertainty. Energy consumption in kilowatt-hours per cubic metre, electrode consumption, membrane flux and the mass of metal-bearing sludge should sit beside percentage removal. Sampling only at the outlet can conceal short-circuiting, sludge carry-over or periodic electrode passivation.
Scale-up also depends on safe maintenance and clear operating limits. New staff need vessel-specific training on electrical isolation, hydrogen, caustic or acidic conditions and chemical handling; safety induction resources can support that process. Emergency plans should cover spills, gas alarms, power loss and isolation of contaminated washdown water.
The Australian operating context
Western Australia is a demanding test market because offshore petroleum activity around Karratha and Port Hedland sits alongside container and bulk shipping through Fremantle and Port Hedland. These operations create maintenance, pilot and retrofit opportunities, but remote turnaround support raises the value of modular equipment that can be serviced without specialist crews travelling long distances.
National rules operate alongside state and port requirements. Ships must comply with international MARPOL controls for oily discharge, while the Australian Maritime Safety Authority covers ship safety and state bodies such as the WA EPA, NSW EPA and EPA Victoria oversee marine pollution. Local port conditions can add monitoring or reporting duties, so an Australian deployment case needs to identify the responsible authority rather than assume one nationwide discharge approval.
Space, vibration and corrosion set hard limits on shipboard skids. Bilge flows vary around port calls, maintenance periods and storm conditions, while engine-room heat and saltwater exposure challenge materials and electronics. Australian operators tend to judge a system by availability, footprint, labour required and lifecycle cost rather than the best removal percentage in a research report.
That preference appears in plain maritime conversation: crews talk about needing to “sort out the bilge” and “get on top of oily discharge”. Procurement is similarly practical, with vessel operators, naval architects, installers and classification bodies checking approved equipment, guarantees and maintenance arrangements. A research prototype still needs pilot acceptance, a credible retrofit plan and a clear route to approved commercial supply.
Moving from reactor tests to ship pilots
The project’s experimental work should compare untreated controls with individual treatment steps and the combined train under controlled conditions. Representative bilge matrices should vary in salinity, oil content, pH and surfactant load. Metal spikes can help identify mechanisms, but real ship samples are needed to expose fouling, variable flow and unexpected interactions between oils, sulfides and electrode materials.
Affiliated laboratories can support this work through replicated reactor tests, membrane performance assessment and independent chemical analysis. Results should follow a mass balance from feed water through oil, digestate, sludge and electrode deposits. Where metal is recovered in solid residues, researchers should characterise its stability so disposal or reuse options can be assessed responsibly.
A ship pilot then needs to answer questions a bench reactor cannot: whether the unit starts after a cold shift, tolerates a large flow slug, requires too much operator attention, or creates unsafe hydrogen or chlorine conditions. Standardised protocols would let research teams and Australian industry partners compare energy use and maintenance rather than relying on incompatible claims.
Follow the ElectroSAnMBR work packages, contact the research team and affiliated laboratories, and support a pilot built around Australian bilge-water conditions. That collaboration can turn promising laboratory separation into evidence that vessel operators, regulators and technology suppliers can trust.