Field test protocol for ElectroSAnMBR under realistic variability
Bilge water is not a stable wastewater stream. Oil content, particles, salinity, temperature, and chemical composition can change within hours as vessels move between engine-room activities, port operations, and weather conditions. A field test protocol for realistic bilge water variability must capture these transients rather than rely on a synthetic feed or one nominal sampling day.
ElectroSAnMBR combines submerged electrolysis, anaerobic digestion, and membrane bioreactor technology. Field trials should assess pollutant removal alongside electrical demand, gas behaviour, membrane flux, fouling, electrode condition, and recovery after shock loads. The unit is evaluated as an operational system, not merely as a set of removal percentages.
A credible comparison pairs the full system with untreated bilge and, where practical, a matched conventional reference. Synchronous influent and effluent sampling establishes baseline behaviour, while event-triggered sampling records oily slugs, high-salinity periods, cleaning events, and unusually dilute discharge. Cleaning, maintenance, downtime, and operating deviations all become part of the performance record.
For Australian users, results must relate to local discharge controls, vessel electrical systems, maintenance capability, and procurement economics. Horizon 2020 research provides the technical basis, while an Australian pilot would test reliability under local climate, schedules, and commercial constraints. Ship operators and suppliers can then compare treatment performance, energy use, maintenance burden, and lifecycle cost.
Test objective and performance envelope
Set the objective as verification of safe, repeatable treatment during normal discharge and representative upset events. Primary endpoints are oil and grease or total petroleum hydrocarbon removal, chemical oxygen demand reduction, solids separation, effluent stability, and compliance with the applicable discharge limit. Secondary endpoints include energy per cubic metre, cleaning frequency, and operator intervention time.
Use the full ElectroSAnMBR beside a matched reference unit or defined conventional process when site constraints permit. Both should receive bilge from the same source, with paired sampling times. This separates the effect of the combined process from changes caused by feed variability, weather, or maintenance.
Lock the performance envelope before operation, including hydraulic retention time, membrane flux, applied current, electrode spacing, temperature, pH, and cleaning intervals. Record deviations rather than silently correcting them. Equipment and training coordination can involve the ElectroSAnMBR research team.
Sampling strategy across operating regimes
Build the sampling plan around actual vessel operations. Use time-proportional composites during routine batches and event-triggered grabs when an oily slug, cleaning discharge, salinity change, or upset occurs. Cover day and night operation where feasible, with at least three independent events in each relevant regime.
Collect samples at influent, membrane permeate or final effluent, and any bypass or reject stream. Characterise oil and grease, TPH, total and soluble COD, suspended solids, pH, conductivity or salinity, temperature, and alkalinity. Add vessel-specific screening for compounds linked to cleaners, hydraulic fluids, fuels, or biocides.
Use a chain-of-custody form linking every bottle to vessel, berth, weather, operating event, and timestamp. Split samples should reconcile field screening with accredited laboratory analysis. Preserve samples promptly and record holding times, because warm Australian conditions can bias volatile compounds and alter emulsified oil samples.
Reactor operation and mass balance
Commission with clean water and stable bilge until the unit reaches repeatable flux, gas balance, and effluent quality. Establish a steady baseline before exposing the reactor to variable feeds. Document membrane condition, electrode surfaces, electrical connections, and baseline water quality before comparative operation.
Continuously log flow, transmembrane pressure, current, voltage, pH, temperature, and gas composition, with alarms tied to the approved operating envelope. Maintain agreed electrical and hydraulic settings, and document every adjustment, cleaning cycle, restart, or power interruption. Check automated logs against operator notes each day.
Calculate mass balances for water, oil and organic load, and relevant chemicals across feed, permeate, concentrate, and sludge. Record gas volume and composition rather than treating output as a simple mass-loss term. This identifies whether apparent removal reflects side-stream transfer, volatilisation, sampling error, or genuine degradation.
Analytical methods and quality assurance
The laboratory suite should match the treatment objectives. Routine analysis covers oil and grease, TPH, COD, BOD, suspended solids, salinity, pH, alkalinity, volatile fatty acids, sulfide, and dissolved oxygen. Analyse methane, hydrogen, and oxygen in the gas stream; use GC-MS or ICP-MS for petroleum compounds, PAHs, metals, or biocides when vessel inventories indicate a risk.
Quality assurance needs field and equipment blanks, duplicates, matrix spikes, calibration checks, and certified reference materials. A practical pilot target is duplicate analysis for roughly one sample in ten and a split sample for each major operating regime. Apply predefined rejection criteria while retaining the original result for transparent reporting.
Link analytical turnaround to the operating log. Volatile or toxic compound samples may need shorter holding times, while delayed COD results can conceal a load excursion. Maintain one validated dataset containing raw results, quality flags, cleaning dates, energy use, and deviations, and compare paired events rather than unrelated averages.
Stress conditions and decision rules
Natural variability should remain the primary challenge. During approved trials, use real bilge across routine, high-oil, high-salinity, dilute, and post-cleaning regimes without introducing pollutants that could compromise the vessel or environment. Any controlled challenge requires an approved surrogate, risk assessment, and separate mass-balance accounting.
Each regime should test shock loading, membrane-fouling tendency, gas and electrode safety, and recovery to stable flux. Watch for emulsion carry-over, grease accumulation, electrode scaling or passivation, and membrane blinding. Record cleaning frequency, effectiveness, chemical demand, and time lost, as these often determine practical viability.
A candidate configuration passes only if it meets applicable oil and chemical limits during every sampled event, keeps membrane and energy performance within the declared envelope, and returns to stable operation after an upset. Report mass-balance closure, commonly within a predefined tolerance such as plus or minus twenty per cent, alongside removals; an average alone can conceal poor worst-case performance.
Australian deployment and regulatory context
Australian siting should reflect vessel traffic. Sydney Harbour and Port Botany provide a demanding case involving cruise, bulk, container, and service vessels, while Melbourne’s Port Phillip Bay combines commercial ports with ferry and small-vessel activity. Align sampling with berth schedules, tidal collection, engine-room routines, and weather that affects ship behaviour.
Deployment must fit Australian regulation and customs workflows. The Australian Border Force manages vessel reporting and border processes, while AMSA and Commonwealth maritime pollution rules, including the Marine Pollution Prevention Act 1999, shape oil-discharge obligations. State, territory, and port controls can add requirements, so confirm legal limits for each site. Method harmonisation can be coordinated with the AA Europa network, while each host confirms local accreditation and chain-of-custody requirements.
The Australian market includes ship owners, charterers, ship managers, repair yards, oily-water service firms, and port reception operators. Retrofitting a skid to 440/690 V shipboard systems while drawing 230/400 V shore power requires isolation and power-quality planning. Vendors will also be judged on maintenance access, parts supply, payback, and verified lifetime performance.
Readiness package and collaboration pathway
A host site should be ready before the first bilge load arrives. The readiness package separates laboratory controls from physical deployment so missing data or safety approvals do not distort the trial.
- Vessel, berth, weather, and operating-event metadata for every sample.
- Calibrated field meters with calibration and drift-check records.
- Preserved bottles, coolers, labels, and a chain-of-custody system.
- Blanks, duplicates, split samples, and accredited laboratory agreements.
- A timestamped master dataset linking samples to reactor logs.
Separate the commissioning requirements from the field campaign. Assign responsibilities, reconcile the data template, and agree how exceptions will be reported.
- Membrane, electrode, power, gas-monitoring, and alarm inspections.
- Site permits, ventilation, emergency isolation, and safe sample handling.
- A matched reference unit or clearly defined comparator treatment process.
- Operator training, standard procedures, and planned maintenance coverage.
- Budgets, spare parts, data-sharing terms, and ownership of results.
Organisations seeking to host a vessel trial, contribute analytical capacity, or evaluate the technology can contact the project contact team. Early engagement can align ship schedules, feed-characterisation data, and safety requirements while preserving the integrity of the comparative field test.