Fate of Emulsified Oils in Anaerobic Electrocoagulation

Shipboard bilge water can contain lubricating oil, hydraulic fluid, fuel residues and other hydrocarbons, usually as a dilute mixture rather than a neat slick. Its most troublesome fraction is emulsified: tiny oil droplets remain suspended by surfactants, colloids and fine solids, preventing gravity separation and increasing the load seen by a treatment system. For Australian operators, reliable removal matters because the Australian Maritime Safety Authority and port authorities oversee ship pollution controls, while MARPOL Annex I sets a 15 ppm oil-content limit for machinery-space bilge water discharges, subject to approved equipment and operating conditions.

ElectroSAnMBR is a European Union Horizon 2020 research project developing a submerged anaerobic electrochemical membrane bioreactor for ship bilge water. By combining electrolysis, anaerobic digestion and membrane separation, it aims to improve removal of oils, chemicals and organic pollutants. Understanding the fate of emulsified oils during electrocoagulation in an anaerobic environment connects those objectives to practical questions: where the oil goes, which products remain and what shipboard data are needed.

Why Emulsified Oil Persists in Bilge Water

Emulsion stability comes from droplet charge and the films surrounding each droplet. Electrical repulsion keeps droplets apart, while surfactants can prevent coalescence. In oily bilge water, the result is often a milky or coffee-coloured dispersion that looks dewatered to a casual observer but still carries substantial hydrocarbon mass. In Australian marine parlance, “blackwater” means sewage, while oily bilge is a separate stream; neither label reveals how much oil remains dispersed.

Droplet size is decisive. Larger globules rise and settle more readily, whereas submicrometre and micrometre droplets remain suspended. Tank-cleaning residues, cargo residues, rust particles and detergents can all create or stabilise these dispersions, so the composition can change substantially between vessels and even between discharge events.

For a treatment plant, this retained oil raises oil-and-grease, chemical oxygen demand and organic carbon loads. Anaerobic digestion can address biodegradable soluble organics, but that does not automatically mean dissolved mineral oil is captured. A sound design therefore tracks both the amount of oil and its physical form.

How Electrocoagulation Destabilises the Emulsion

In electrocoagulation, sacrificial iron or aluminium anodes release metal ions that form hydroxide coagulants around suspended material. These coagulants neutralise droplet charge, bridge particles and sweep droplets into larger flocs. Cathodic hydrogen bubbles can also attach to hydrophobic oil, encouraging flotation, while settling and membrane capture provide competing routes for separation.

The anaerobic setting changes the chemistry without stopping electrolysis. Cathodic reactions still generate hydrogen and alkalinity, and local pH near the electrodes affects coagulant formation. Bulk conditions must remain sufficiently buffered because acidic bilge water can increase electrode corrosion, while excessive alkalinity can alter floc structure. Oxygen exclusion reduces aerobic oxidation, so the process should not be described as simple burning of the oil.

Oil may therefore leave the treatment train in several forms: as part of a settled or floated sludge, as material retained on the membrane, as droplets broken into smaller fragments, or as residual soluble and finely dispersed hydrocarbons. Direct electrochemical cleavage can affect some compounds, but droplet destabilisation and phase separation are usually the dominant roles to test.

Fate Through the Anaerobic Membrane Bioreactor

A submerged membrane bioreactor retains biomass and solids in a reactor where hydrolysis, acidogenesis, acetogenesis and methanogenesis proceed without oxygen. Hydrolysis converts larger oily molecules and emulsifying materials into smaller compounds. Adapted microbial consortia may then convert biodegradable fractions, while methane production indicates whether the organic load is being converted usefully rather than merely stored in the sludge.

Not every hydrocarbon is readily biodegradable. Recalcitrant fractions can remain associated with flocs or membrane foulants, and surfactants may alter microbial activity. Electrolysis can also yield intermediate organic compounds that are more soluble than the parent oil. A laboratory methane result should therefore be checked against a complete oil and carbon balance.

Dissolved iron or aluminium may react with sulfide, phosphate and carbonate in anaerobic sludge, forming metal-bearing solids. These solids can improve floc density but also contribute to membrane fouling. The coupled process must balance oil capture, biogas production, sludge stability and membrane permeability rather than optimise current density in isolation.

Measuring the Fate of Emulsified Oils

A credible experiment needs controls for untreated bilge water, electrolysis without biological activity, biological treatment without electrocoagulation and the fully coupled reactor. These comparisons separate physical recovery from biodegradation and expose any inhibitory effect caused by oil, surfactants or electrode-derived metals.

Sampling should cover feed, reactor mixed liquor, membrane permeate, separated sludge and electrode or flotation residues. Oil-and-grease measurements can be paired with total organic carbon, chemical oxygen demand, volatile fatty acids and methane tracking. Microscopic droplet-size analysis, turbidity and, where available, zeta potential help determine whether the emulsion has truly destabilised. Gas chromatography can identify targeted hydrocarbons when a finer chemical breakdown is required.

The energy charge, electrode consumption, sludge production and membrane flux belong in the same mass balance. Reproducing this work at Australian vessel scale also requires reference samples from relevant ports and ship types, because fuel, lubricants, detergents and bilge-water practices vary by route and operation.

Field Indicators and Operating Controls

The following measurements connect laboratory fate pathways with routine plant performance:

They should be interpreted together. A lower permeate oil result does not prove that all oil was destroyed, while strong methane production does not guarantee that persistent hydrocarbons were removed.

Key operating controls include:

Australian crews already monitor machinery spaces closely during demanding schedules, including FIFO offshore rotations and vessel maintenance windows. Compact instrumentation and clear pass/fail thresholds would help operators avoid treating a visible oily sheen as evidence that the full oil load has been removed.

Scale-Up for Australian Commercial Vessels

MARPOL limits are only the starting point. The equipment also has to fit narrow engine rooms, tolerate vibration, run in a hot environment and be maintainable by shipboard staff or local technicians. A reactor that performs well in a university laboratory but fouls rapidly after one tropical voyage in the Gulf of Carpentaria would offer little operational value.

Australia provides demanding test settings: bulk carriers and coastal trades work through the Port of Brisbane and Gladstone, offshore support vessels service resource operations, and shipyards around Henderson in Western Australia and Newcastle conduct dry-dock refits. These are not identical applications. A unit serving offshore bases needs high availability and simple maintenance; a harbour installation may prioritise footprint and treatment cost.

Commercial uptake depends on how the system is bought and serviced. Owners may prefer a retrofit package, a voyage-based rental, or a treatment service incorporated into a charter arrangement, with electricity, electrode replacement and waste disposal included in the total cost. Local electrical contractors and shipyards can influence installation standards, while imported specialist components introduce lead-time and spare-parts risks. The project's commercial vessel economics analysis offers a useful basis for comparing those models.

From Laboratory Evidence to Shipboard Action

The next step is to validate the coupled process using representative Australian oily bilge water and realistic operating interruptions. Trials should track not only discharge concentrations, but oil mass recovery, sludge fate, membrane cleaning frequency, energy use and effects on the downstream sludge stream. This avoids declaring success from a single clean-looking sample while residual emulsions and contaminated solids remain unresolved.

Review the ElectroSAnMBR objectives, work packages and experimental methods, then contact the project's research partners to discuss vessel trials, analytical collaboration and pathways from laboratory validation to commercial deployment.